Wen 70712 12 Sliding Compound Miter Saw Manuel d'utilisateur

ITEM 70712 OPERATOR’S MANUAL 10 ELECTRICAL INSTRUCTIONS Grounding Instructions 1. IN THE EVENT OF A MALFUNCTION OR B

ITEM 70712 OPERATOR’S MANUAL 11 Fig. 1 1. Tools/equipment with three wire grounding plugs (Fig. 1, A) are intended

ITEM 70712 OPERATOR’S MANUAL 12 1. Be sure your extension cord is properly wired and in good condition. Always repl

ITEM 70712 OPERATOR’S MANUAL 13 COMPONENTS ASSEMBLY INSTRUCTIONS Extension Supports Attachment Insert the ends of th

ITEM 70712 OPERATOR’S MANUAL 14 Note: the saw is shipped with the motor locked in the down position. To release the s

ITEM 70712 OPERATOR’S MANUAL 15 lock the Table into several often used miter angles. These angles are 0º (centered),

ITEM 70712 OPERATOR’S MANUAL 16 Bevel Angle Adjustment 1. A bevel cut is one that is at an angle to the vertical pla

ITEM 70712 OPERATOR’S MANUAL 17 Squaring the Saw Blade to the Guide Fence WARNING: Be sure that the Miter Saw is swit

ITEM 70712 OPERATOR’S MANUAL 18 5. Slowly rotate the blade by hand, checking the square's alignment with the bl

ITEM 70712 OPERATOR’S MANUAL 19 9. When the cut is completed, raise the Blade Assembly, wait for the blade to stop t

ITEM 70712 OPERATOR’S MANUAL 2 MITER SAW IDENTIFICATION For information and questions contact customer service at 1-8

ITEM 70712 OPERATOR’S MANUAL 20 Cutting Odd Shapes, Oversize or Small Pieces 1. Plan your work so an odd shaped work

ITEM 70712 OPERATOR’S MANUAL 21 18. Test the operation of your saw prior to cutting a work piece. If you feel excessi

ITEM 70712 OPERATOR’S MANUAL 22 Blade Replacement 1. Unplug the tool from its power source. 2. Lock the Blade Asse

ITEM 70712 OPERATOR’S MANUAL 23 5. If either test reveals that the cut is not a true 90º angle, you must adjust the

ITEM 70712 OPERATOR’S MANUAL 24 Miter Saw Cleaning and Lubricating 1. Observe the Dust Bag while using the saw. Empt

ITEM 70712 OPERATOR’S MANUAL 25 TROUBLESHOOTING Problem Possible Causes Likely Solutions Miter Saw will not start. N

ITEM 70712 OPERATOR’S MANUAL 26 EXPLODED VIEW

ITEM 70712 OPERATOR’S MANUAL 27 PARTS LIST Part # Stock # Description Part # Stock # Description 1 70712-001 LOCK N

ITEM 70712 OPERATOR’S MANUAL 28 Part # Stock # Description 87 70712-087 PLASTIC COVER 88 70712-088 SPRING 89 70712-08

ITEM 70712 OPERATOR’S MANUAL 29 ONE (1) YEAR LIMITED WARRANTY WEN® is committed to building tools that are dependabl

ITEM 70712 OPERATOR’S MANUAL 3 TABLE OF CONTENTS Specifications …………………………………………………….. 4 Important Safety Instructi

ITEM 70712 OPERATOR’S MANUAL 4 SPECIFICATIONS 12" Sliding Compound Miter Saw Package Contents Sliding Compound

ITEM 70712 OPERATOR’S MANUAL 5 IMPORTANT SAFETY INSTRUCTIONS 1. The purpose of safety symbols is to attract your att

ITEM 70712 OPERATOR’S MANUAL 6 Work Area Safety 1. Keep your work area clean and well lit. Cluttered or dark areas i

ITEM 70712 OPERATOR’S MANUAL 7 WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con

ITEM 70712 OPERATOR’S MANUAL 8 6. Allow the motor to come up to full speed before starting a cut to avoid binding or

ITEM 70712 OPERATOR’S MANUAL 9 WARNING: Do not operate your saw until it is assembled, and you have read and understo