Wen 4210 10 Variable Speed Drill Press Manuel d'utilisateur

4212 WENPRODUCTS.COM 10 Assembly and adjustments (continued) WARNING: If any part is missing or damaged, do not plug the drill press in unti

4212 WENPRODUCTS.COM 11 Assembly and adjustments (continued) Note: Make sure there is enough clearance to allow the table to rotate around the

4212 WENPRODUCTS.COM 12 Assembly and adjustments (continued) Speed handle (Fig. 8) 1. Insert the feed handle (1) into the threaded opening o

4212 WENPRODUCTS.COM 13 Assembly and adjustments (continued) Table adjustments Raise or lower the table (Fig. 11) 1. Loosen the support lock

4212 WENPRODUCTS.COM 14 Assembly and adjustments (continued) Laser batteries (Fig. 13) 1. Turn off the laser. 2. Press the tab (1) located b

4212 WENPRODUCTS.COM 15 Assembly and adjustments (continued) Spindle return spring (Fig. 15) The spindle is equipped with an auto-return mecha

4212 WENPRODUCTS.COM 16 Operation Drill Press ON/OFF switch (Fig. 17) 1.

4212 WENPRODUCTS.COM 17 Operation (continued) Drilling speeds Important factors when determining the best drilling speed:  Material type 

4212 WENPRODUCTS.COM 18 Operation (continued) Mechanical variable speed (Fig. 18) This is a mechanical variable speed drill press. To increase

4212 WENPRODUCTS.COM 19 Maintenance WARNING: For your safety, turn the switch off and remove the plug from the power supply before maintaini

4212 WENPRODUCTS.COM 2 Table of Contents Technical data………………………………………………………………………………. 2 General safety rules……………………………………………………………………….

4212 WENPRODUCTS.COM 20 Troubleshooting PROBLEM Noisy operation The drill bit burns or smokes. Excessive drill run-out or

4212 WENPRODUCTS.COM 21 Troubleshooting (continued) PROBLEM The workpiece splinters on the underside. The workpiece is slipping from your ha

4212 WENPRODUCTS.COM 22 Replacement parts Service Information Now that you have purchased your bench top power tool, should a need ever exist

Parts list Item Stock # Description Item Stock # Description 1 4212-001 Column 41 4212-041 Knob 2 4212-002 Rack 44 4212-044 Screw M8x25 3 42

4212 WENPRODUCTS.COM 24 Parts list (continued) Item Stock # Description Item Stock # Description 86 4212-086 Sleeve 97 4212-097 Screw M8x8 87

4212 WENPRODUCTS.COM 25 Exploded view

4212 WENPRODUCTS.COM 26 Two years limited warranty WEN® is committed to building tools that are dependable for years. Our warranties are consis

4212 WENPRODUCTS.COM 27

4212 WENPRODUCTS.COM 3 General safety rules Safety is a combination of common sense, staying alert, and knowing how your drill press works.

4212 WENPRODUCTS.COM 4 General safety rules (continued) 13. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. Do not leav

4212 WENPRODUCTS.COM 5 Specific safety rules for the drill press WARNING: Do not operate the drill press until it is completely assembled an

4212 WENPRODUCTS.COM 6 1 - 3-prong plug 2 - Properly grounded outlet 3 - Grounding prong Electrical information Grounding instructions IN TH

4212 WENPRODUCTS.COM 7 Electrical information (continued) WARNING: This drill press is for indoor use only. Do not expose to rain or use i

4212 WENPRODUCTS.COM 8 Know your drill press Fig. 1 1 Speed control handle 2 Support lock handle 3

4212 WENPRODUCTS.COM 9 Assembly and adjustments Unpacking Unpack the drill press and all its parts, and compare against the list below. Do