Wen 4210 Manuel d'utilisation et d'entretien

10 Assembly and adjustments (continued) Tools needed for assembly • Adjustable wrench • Phillips® screwdriver • Hammer and block of wood Base

11 Assembly and adjustments (continued) 6. Place the collar (1) bevel side down over the rack. Tighten the set screw (2) with the 3 mm Allen wre

12 Assembly and adjustments (continued) Feed handles (Fig. 9) 1. Thread the three feed handle rods (1) into the holes on the feed hub (2). 2.

13 Assembly and adjustments (continued) Mount the drill press (Fig. 12) Your drill press must be securely fastened through the mounting holes (1

14 Assembly and adjustments (continued) Remove the chuck (Fig. 14) 1. Turn the feed handles (1) to lower the chuck (2) to the lowest position.

15 Assembly and adjustments (continued) Adjustments Align the belt pulleys (Fig. 16) 1. Check the alignment of the pulleys with a straight edg

16 Assembly and adjustments (continued) WARNING: Disconnect the drill press from the power source before making any speed adjustments. Adjust spe

17 Assembly and adjustments (continued) Tilt the table (Fig. 20) The table can be tilted from 0 to 45° to the left and right. 1. Loosen the b

18 Assembly and adjustments (continued) Drilling depth (Fig. 22) 1. To stop the drill at a specific depth for consistent and repetitive drilling

19 Assembly and adjustments (continued) Angular play of the spindle (Fig. 24) Move the spindle to the lowest downward position and hold in place

2 Table of Contents Technical data………………………………………………………………….. 2 General safety rules…………………………………………………………….. 3 Specific safety rules for dril

20 Assembly and adjustments (continued) WARNING: DO NOT STARE DIRECTLY AT THE LASER BEAM! A hazard may exist if you deliberately stare into the be

21 Operation Switches (Fig. 28) 1. To turn the drill press ON, insert the safety key (1) into the switch housing (2). As a safety feature, the s

22 Operation (continued) WARNING: To avoid injury, make sure the chuck key is removed from the chuck before starting any drilling operation. Dr

23 Operation (continued) Depth scale method (Fig. 31) 1. With the switch (1) OFF, turn the feed handle (2) until the drill bit tip (3) slightly

24 Operation (continued) Drilling metal  Use metal-piercing twist drill bits.  It is always necessary to lubricate the tip of the drill with

25 Maintenance WARNING: For your own safety, turn the switch OFF and remove the plug from the power source before maintaining or lubricating the

26 Exploded view

27 Parts list No. Stock # Description Qty No. Stock # Description Qty 1 4210-001 Column tube 1 43 4210-043 Lock washer 2 2 4210-002 Rack 1 44 421

28 Limited Two Years Warranty WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commi

3 General safety rules Safety is a combination of common sense, staying alert, and knowing how your drill press works. SAVE THESE SAFETY INSTRUCTI

4 General safety rules (continued) 13. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. Do not leave the tool until it has come

5 Specific safety rules for drill presses WARNING: Do not operate your drill press until it is completely assembled and installed according to the

6 Electrical information Grounding instructions IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for

7 Electrical information (continued) WARNING: This drill press is for indoor use only. Do not expose to rain or use in damp locations. Guidelin

8 Know your drill press A Power cord K Motor pulley U Light bulb(not provided) B Tension lock knob L Motor V Quill C Pulley housing cover M Feed

9 Assembly and adjustments Unpacking (Fig. 2) Unpack the drill press and all its parts, and compare against the list below. Do not discard the ca