Wen 4214 Manuel d'utilisation et d'entretien

Model # 421412˝ VARIABLE SPEED DRILL PRESSbit.ly/wenvideoYour new tool has been engineered and manufactured to WEN’s highest standards for dependabili

10ASSEMBLY AND ADJUSTMENTSDRILL PRESS HEAD TO COLUMN (Fig. 5)CAUTION: The drill press head is heavy. To avoid injury, two people should lift it into p

11ASSEMBLY AND ADJUSTMENTSMOUNT THE DRILL PRESS (Fig. 8)The drill press must be securely fastened through the mounting holes to a stand or workbench w

ASSEMBLY AND ADJUSTMENTS12RAISE OR LOWER THE TABLE (Fig. 11)1. Loosen the support lock handle (1) and turn the crank handle (2) until the table is at

ASSEMBLY AND ADJUSTMENTS13WARNING: To avoid injury, make sure the chuck key is removed from the chuck before starting any drilling operation.INSTALLIN

14ASSEMBLY AND ADJUSTMENTSADJUSTING THE LASER (Fig. 15 and 16)WARNING: Do not stare directly at the laser beam. Please observe all safety rules.• Neve

15ASSEMBLY AND ADJUSTMENTSANGULAR “PLAY” OF THE SPINDLE (Fig. 18)Move the spindle to the lowest downward position and hold in place. Try to make the s

16OPERATIONDRILL PRESS ON/OFF SWITCH (Fig. 20)1. To turn the drill press ON, insert the yellow safety key (1) into the switch housing (2). As a safety

17OPERATIONADJUST THE DRILLING DEPTH (Fig. 22)The depth gauge controls the maximum distance the drill bit will move up or down.To stop the drill bit a

18OPERATIONDRILLING SPEEDSThere are a few important factors to keep in mind when determining the best drilling speed:• Material type• Hole size• Drill

19OPERATIONWARNING: For your safety, turn the switch off and remove the plug from the power supply before maintaining or lubricating the drill press.V

TABLE OF CONTENTSTechnical Data2345781619202124General Safety RulesSpecific Safety Rules For Drill PressElectrical InformationKnow Your Drill PressAss

TROUBLESHOOTINGPROBLEM CAUSES SOLUTIONSNoisy operation 1) Incorrect belt tension2) Dry spindle3) Loosed spindle pulley4) Loosed motor pulley1) Adjust

EXPLODED VIEW & PARTS LIST21

EXPLODED VIEW & PARTS LIST22Item # Stock # Description Qty1 4214B-001 Circlip 12 4214B-002 Cam 13 4214B-003 Screws M8x12 14 4214B-004 Bearing 619

EXPLODED VIEW & PARTS LIST23Item # Stock # Description Qty89 4214B-089 Rack shaft 190 4214B-090 Big washer 8 191 4214B-091 Bolt M8x12 492 4214B-09

WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to qu

3GENERAL SAFETY RULESSafety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING:

414. NEVER STAND ON A TOOL. Serious injury could result if the tool tips or is accidentally hit. DO NOT store anything above or near the tool. 15. DO

5SPECIFIC RULES FOR DRILL PRESS10. Always stop the drill before removing scrap pieces from the table.11. Use clamps or a vise to secure a workpiece to

GUIDELINES FOR USING EXTENSION CORDSMake sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough

7AMPERAGEREQUIRED GAUGE FOR EXTENSION CORDS25 ft. 50 ft. 100 ft. 150 ft.5 A 18 gauge 16 gauge 16 gauge 14 gaugeKNOW YOUR DRILL PRESSDigital Speed Read

88ASSEMBLY AND ADJUSTMENTSUNPACKING (Fig. 2)Unpack the drill press and all of its parts. Compare against the list below. Do not discard the carton or

9ASSEMBLY AND ADJUSTMENTSWARNING: If any part is missing or damaged, do not plug the drill press in until the missing or damaged part is repaired or r